Our New On-Demand Library of Training Videos

See how it's done with these complimentary videos.

Quick-start guide

What you'll receive with your Ambrell EASYHEAT (1.2-2.4kW) system and how to set it up and get going in a matter of just minutes.

Heating

Learn how to heat with an EASYHEAT model. This video is intended to be viewed after the EASYHEAT Quick Start Video.

Rear panel start

Learn how to configure an EASYHEAT (1.2-2.4kW) to start from the rear panel.

One or Two Button Start

Learn how to configure your EASYHEAT (1.2-2.4kW) for a one button (press to heat) or two-button (on/off start/stop) start.

Set Capacitance Value

How to change the capacitance value after changing caps on an EASYHEAT (1.2-2.4kW) induction heating system.

Changing taps

Learn how to change transformer taps on an EASYHEAT (1.2-2.4kW) induction heating system.

Controlling Setpoint

Learn how to configure the EASYHEAT (1.2-2.4kW) to control the setpoint using the remote input on the rear of the unit.

Verifying the Values of Capacitors Inside

Verifying Capacitance

Learn how to verify the values of the capacitors inside the EASYHEAT (1.2-2.4kW) heat station.

Verify heat station model

Learn how to verify that the heat station model number is set correctly on an EASYHEAT (1.2-2.4kW).

Configure Firmware for RS-485 Communications

Learn how to configure firmware for RS-485 communications on an Ambrell EASYHEAT (1.2 - 2.4 kW) induction heating system

Install 003-0349 Card, EASYHEAT 1.2-2,4kW

Learn how to install an 003-0349 card on an EASYHEAT (1.2-2.4 kW) induction heating system.

Quick-start guide

learn how to get started with your new EASYHEAT LI induction heating system.

Heating

Learn how to change capacitors and taps to heat with your EASYHEAT LI in an optimal manner.

Changing Capacitance

How to change the capacitance value of an EASYHEAT LI's capacitors.

Using Frequency Offset

The frequency offset feature on the Ambrell EASYHEAT LI induction heating system.

Quick-start guide

Learn how to setup your new EKOHEAT 10-15 kW/50-150 kHz induction heating system.

Changing Taps

How to change transformer taps on your Ambrell EKOHEAT Induction Heating System.

Three heating modes

15-20 words about the video. Link to relevant stand-alone video page and to relevant product if possible.

Low Level Scan/Learn Start Frequency

Ambrell VPA power supplies have two utilities useful for determining tap and choke selection as well as the appropriate start frequency

AMBRELL CORPORATION

1655 Lyell Avenue
Rochester, NY 14606
United States

F: +1 585 889 4030

AMBRELL B.V.

Holtersweg 1
7556 BS Hengelo
The Netherlands

Directions to Ambrell B. V. Directions

F: +31 546 788 154

AMBRELL Ltd.

Unit 6, Space Business Centre
Tewkesbury Road
Cheltenham, GLOS, GL51 9FL
United Kingdom

F: +31 546 788 154

Our New On-Demand Library of Training Videos

See how it's done with these complimentary videos.

Our New On-Demand Library of Training Videos

See how it's done with these complimentary videos.

Select an option below:

Quick-start guide

Heating

Rear panel start

One or Two Button Start

Set Capacitance Value

Changing taps

Controlling Setpoint

Verifying Capacitance

Verify heat station model

Configure Firmware for RS-485 Communications

Install 003-0349 Card, EASYHEAT 1.2-2,4kW

Quick-start guide

Heating

Changing Capacitance

Using Frequency Offset

Quick-start guide

Changing Taps

Three heating modes

Low Level Scan/Learn Start Frequency

Four Ways To Contact Ambrell for Support

AMBRELL CORPORATION

AMBRELL B.V.

AMBRELL Ltd.

VISITOR RESOURCES

INDUSTRY EXPERTISE

PRODUCTS

ABOUT